Electronics/RF Technician III
Epiq Design Solutions LLC
·Today
- Salary
- $74k – $110k/yr
- Location
- Frederick, MD
- Seniority
- Senior
- Education
- Associate
- Source
- Paylocity
Description
Description
COMPANY BACKGROUND
Epiq Solutions develops cutting-edge software-defined radio (SDR) products and processing solutions to enable spectrum dominance for maritime, land, air, and space domains. With 17 years serving government and commercial enterprise customers and 25K+ devices fielded to date, Epiq Solutions is a trusted partner with a proven heritage of delivering open architecture products in radically small form factors where time-to-market, cost, and performance are critical for mission success.
For more information, visit https://epiqsolutions.com.
JOB SUMMARY
We are seeking an experienced Electronics/RF Technician III to support the development, testing, and repair of custom and commercial SDR solutions. This position performs complex component-level, board-level, unit-level, and system-level RF testing, troubleshooting, and repair in accordance with established test procedures and applicable quality standards.
This senior technician restores and maintains test capability, performs and optimizes approved FNR adjustments, leads complex return material authorization (RMA) evaluations and repairs, supports new product introduction (NPI), and mentors Technician I and II employees.
JOB RESPONSIBILITIES
- Lead complex unit-level and system-level testing and correlate bench results, automated test equipment (ATE) results, configurations, environmental conditions, and product history.
- Maintain ATE technical readiness through scheduled maintenance, calibration coordination, reference-unit checks, measurement correlation, fixture and cable control, and rapid diagnosis of rack-related failures.
- Analyze gain, IP3/IIP3, internally generated spurs, noise figure, bandwidth, isolation, rejection, phase noise, compression, and other advanced final-test measurements.
- Perform and optimize approved FNR adjustments to meet specifications while monitoring effects on gain, IP3, noise, spurious response, and related parameters.
- Troubleshoot complex RF, analog, digital, and mixed-signal failures at the component, board, assembly, unit, system, and test-environment levels.
- Perform component-level fault isolation and repair using schematics, layouts, datasheets, signal tracing, voltage and waveform measurements, and comparison to known-good circuits.
- Remove and replace failed or suspect RF, analog, digital, power, and mixed-signal components using approved soldering and rework methods; inspect workmanship and verify repair integrity.
- Validate component-level repairs by repeating applicable bench, unit-level, system-level, and ATE testing and documenting the cause, repair action, and verification results.
- Independently tune and align RF/microwave assemblies operating at frequencies up to approximately 24 GHz and demonstrate proficiency in testing and troubleshooting assigned products operating at frequencies up to 40 GHz.
- Lead the technical aspects of containment, root-cause analysis, corrective action, and recurrence prevention.
- Lead complex RMA troubleshooting and repair, develop evidence-based conclusions, verify corrective actions at unit and system levels, and prepare or technically review complete RMA reports.
- Develop and improve test procedures, component-level troubleshooting guides, repair instructions, fixtures, rack checks, and production documentation.
- Support prototype, pilot, and NPI builds, and mentor Technician I and II employees.
- Perform other duties as assigned.
Requirements
Required Qualifications
- Technical certificate or associate degree in electronics, electrical engineering technology, RF/microwave technology, or a related field; or an equivalent combination of education and relevant experience.
- At least five years of experience in an electronics manufacturing environment, including RF testing, troubleshooting, and repair.
- Advanced knowledge of RF theory, including S-parameters, impedance matching, spurious signals, noise, compression, and measurement uncertainty.
- Advanced ability to isolate failures to individual components or circuit stages and complete controlled repair and verification on RF-sensitive assemblies.
- Advanced knowledge of ATE architecture, calibration dependencies, and measurement correlation, including the ability to distinguish product failures from test-environment issues.
- Proven success resolving intermittent, multi-variable, recurring, or system-level failures.
- Ability to communicate technical findings and practical corrective actions across production, engineering, and quality.
- Proficiency with Microsoft Office applications.
- Strong attention to detail, effective communication skills, and the ability to work collaboratively and adapt to changing priorities.
- Eligibility to work on federal contracts that require U.S. citizenship.
Preferred Qualifications
- IPC-A-610 and/or J-STD-001 training or certification appropriate to the work performed.
- Experience in high-reliability or controlled electronics manufacturing, preferably in aerospace, defense, or communications.
- Familiarity with ESD control, calibration systems, 5S/6S, lean manufacturing, and structured problem-solving.
BENEFITS
- Join a successful and growing company investing in our future success
- Generous vacation policy
- Paid five-week sabbatical every five years
- 401(k) company match
- Health, dental, vision insurance
- Life and long-term disability insurance
- Employee assistance program
- Wellness reimbursement
- Charitable giving company match
- Competitive salary commensurate with experience and performance
- Fun, laid-back culture and rewarding work!
Epiq Solutions is an Equal Employment Opportunity Employer - All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, disability, or status as a protected veteran.