Electrical / Electronics Architect
Philips
·Today
- Location
- Pune - Chakan Office-Factory, India
- Workplace
- Onsite
- Type
- Full-time
- Department
- Engineering
- Seniority
- Lead
- Experience
- 12+ years
- Source
- Workday
Description
Job Title
Electrical / Electronics ArchitectJob Description
To succeed in this role, you should have the following skills and experience:
- Completed engineering studies at University level; BE/BTech/ME/M-Tech in Electronics or Electrical Engineering, with 12+ years of experience
- Knowledge of state-of-the-art methods/tools (CAD/simulation) used in electrical design
- Experience in High-Speed Digital electronics, Mixed Signal Board Design
- Experience in complex FPGA Designs (Hardware Interface exposure)-16/32-bit microcontroller-based design and interfacing
- High Speed Memories such as DDR4, DDR5
- Knowledge of cable harness design, Semiconductor Active/Passive component selection
- Should have good fundamental knowledge of Motors/Motor Drivers/ Position, Speed
- Encoders and should be able to analyze motor under different operating modes such as regenerative mode, Motion control techniques & interfaces with motors/actuators
- Knowledge of communication interfaces like RS232, RS485, CAN, EtherCAT, Ethernet and USB , UART, CAN, SPI, I2C.
- Knowledge of EMI/EMC standards and testing for conformance
- Good understanding of design tools: Mentor Graphics (Schematic entry), LTspice / Pspice
- Should have experience in DFMEA and design of Fail-safe systems and Sub systems
- Good understanding of Linear regulators, LDOs, and DC-DC converter topologies
- Experience in the design of a communication gateway will be an added advantage.
- Should have experience in the design of high-speed circuits and digital interfaces eg. DDR4, EEPROM, QSPI flash, USB, Ethernet.
- Should be aware of electromagnetic fields and the design of electronics for high ambient magnetic and electromagnetic fields
- Should have an understanding of patient safety with knowledge of Insulation Diagram and means of Protection (MOPP/MOOP)
- Ability to understand cross-stream requirements Eg. mechanical design, FPGA, Firmware compatibility aspects
- Experience in Advance development & New Product Introduction (NPI) and Product Life Cycle Management, Product Obsolescence Management/Sustenance Engineering
- Ability to understand and debug problems across hardware/software boundaries
- Knowledge of Global Medical Quality and Regulatory Standards e.g. IEC, FDA, UL, CE, CSA etc. will be an added advantage
- Hands-on experience with tools like Agile, ClearQuest, Windchill, ALM or equivalent
- Able to guide and mentor young engineers in the team with a result-oriented team player
- Ability to present and articulate ideas to key stakeholders and leadership team
- Excellent communication skills and a positive ‘can-do’ attitude with a quality mindset during design and documentation creation
- Global and Cross-functional Experience/Skills in a Matrix Organization will be an added advantage
Desired Skills
- Experience in design or selection of off-the-shelf battery charger and battery management system will be an added advantage
- Analog Design expertise is added value
You are responsible for:
- The Hardware Engineer is responsible for participating in design reviews and technical discussions and providing valuable insights + recommendations on hardware design considerations, trade-offs, and potential optimizations, working under limited supervision.
- Own the requirements, design, implementation, test and integration of module/sub-system in accordance with the higher-level architectural requirements and design specifications
- Ensuring that the design is consistent with the higher-level architecture and requirements
- Ensuring that the proposed design would have the safety, reliability and quality features built-in
- Responsible for ensuring that the design meets the performance, quality and cost criteria
- Conduct concept and feasibility studies. Leads the introduction of new technologies
- Ensuring that there is proper documentation per standards for the developed design
- Ensuring the mutual consistency and efficient integration of the separate components in modular design that meets the product specification
- Ensuring that his design modules meet the product certification requirements
- Drawing up personal schedule and reports on progress
- Defining and assessing the Work Breakdown Structure/planning/costs of his/her area
- Being abreast of technical developments in own field through study of literature and technical contacts
- Mentoring/guiding/hand-holding young engineers in the team and helping them ramp-up well
- Maintaining product and company reputation by complying with country specific regulations Supplier evaluation and communication
How we work together
We believe that we are better together than apart. For our office-based teams, this means working in-person at least 3 days per week. Onsite roles require full-time presence in the company’s facilities. Field roles are most effectively done outside of the company’s main facilities, generally at the customers’ or suppliers’ locations.
About Philips
Are you ready to do the work of your life to help the lives of others? Learn more about our business, discover our rich and exciting history and learn more about our purpose.
If you’re interested in this role and have many, but not all, of the experiences needed, we encourage you to apply. You may still be the right candidate for this or other opportunities at Philips. Learn more about our culture of impact with care.
#LI-Philin